MH8000PP The Combo unit integrates EMS and TENS functions with 7 treatment modes. This unit is a hybrid stimulator which can be used for muscle stimulation and pain relieve.

Transcutaneous Electrical Nerve Stimulation (TENS), designed for symptomatic relieve and management of chronic intractable pain. TENS is a safe non-invasive drug-free method of pain management. "Transcutaneous" means across the skin. It relieves pain by sending tiny electrical impulses through electrodes placed on or near the area of pain or pressure point to underlying nerve fibers.

Electrical Muscle Stimulation (EMS) is an advanced muscle exercise muscle toning technique that is an efficiently & effectively supplement to your workout routine. Our EMS units are portable, light weight and battery-powered electronic units. EMS units are designed to exercise body muscles by applying a chosen intensity and frequency of electrical current repeatedly in a series of stimulated contraction & relaxation phases.

Features:
1. TENS and EMS Two in one: Our products support full TENS and EMS functions with 7 treatment modes, ideal for home health care.
2. Large Liquid Crystal Display (LCD): Large LCD can display intensity level, settings and treatment timer at the same time. The information shown in a large font can make it easier for elder users to read.
3. Key Pad control: Power, intensity level and parameter are input by Key pad. It's easy for users to input their settings. All buttons will be auto-locked after 30 seconds idle time to avoid accidental touch.
4. Adjusting Intensity Level precisely: Intensity Level can be increased from 0 by 1mA each step up to 80mA. Precise and smooth adjustments in Intensity Level can prevent the user a sudden adjusting the intensity of too much danger.
5. Electrode Detection (Optional Function): The unit with electrode detection function, the Intensity level will be reset at 0 when an electrode open circuit is detected.
6. Clear Treatment Time: The treatment time count down and the balance treatment time can be read from the LCD.
7. Compliance Meter: The patient compliance timer can memorize 100 sets of therapy session records; the total record time is 400 hours. Doctors can tell whether a patient could continue treatment in accordance with the instructions.
8. ON and OFF time indicator: For EMS function, the Intensity Level that displays on the LCD screen will accordingly switch among Ramp time, ON time and OFF time. This makes it easier for the patient to know to turn up the intensity only during the ON Time, otherwise, the patient might accidentally turn the amplitude way up during the OFF Time, and suddenly have too much stimulation when the unit comes back to ON Time.
9. LOW BATTERY INDICATOR: A low battery indicator will flashes on the LCD only when the battery is low.

The device detailed information:
1. Dual Channel, isolated between channels.
2. Timer setting from 5-90 Minutes, 5min./step, or continue.
3. Time count down monitored on LCD screen.
4. Automatic switch off after 30 seconds if unit is not in use.
5. CE 0434, FDA (510k)
6. Waveform: Asymmetrical rectangular biphasic pulse.
7. Amplitude: 0 - 80 mA into 500 ohm load.
8. Selectable pulse width: Adjustable, from 50us - 300us, 10us/step.
9. Pulse Rate: Adjustable, from 2 Hz - 150 Hz, 2Hz~20 Hz in 1 Hz/step and 20~ 150 Hz in 5 Hz/step.
10. Modes for EMS: The EMS is an intermittent stimulation. The pulse active and inactive duration are adjustable by setting ON time and OFF time. The contraction gradually increases during ramp-up time and reaches maximum contraction during ON time. During ramp-down time, the contraction gradually decreases until the OFF time starts.
S (Synchronous) Mode: Stimulation of both channels will occur simultaneously.
A (EMS with Rate Modulation) Mode: This mode is an EMS mode with Rate Modulation stimulation.
11. Modes for TENS:
N (Normal) Mode: Continuous output, pulse rate and pulse width are adjustable.
M (Rate and Width Modulation) Mode: Per cycle time is 1 second. Each cycle contains two phases. During the first 0.5 sec. phase, the Pulse Width runs at 50% of its width setting and Pulse Rate runs at its rate setting, then during the second 0.5 sec. phase, the Pulse Rate runs at 50% of its rate setting and Pulse width runs at its width setting. The cycle is then repeated.
B (Burst) Mode: Pulse width is adjustable from 50~300uS in 10uS per step, Frequency is fixed at 100 Hz, Burst rate is fixed at 2 Hz.
SD (Width Modulation) Mode: Pulse Width is modulated over a period of 3 seconds from its original setting value down to 60% of its setting, then modulated over another 3 seconds period at its original value. The cycle is then repeated. Per cycle time is 6 seconds.
MR (Rate Modulation) Mode: Pulse Rate is modulated over a period of 3 seconds from its original setting value down to 60% of its setting, then modulated over another 3 seconds period at its original setting. The cycle is then repeated. Per cycle time is 6 seconds.
12. Open Electrode Detect: If an open circuit is detected at the output of channel 1 or 2 the output current will be reset at zero. This is an option function and only active in Pulse Width between from 100uS and 300uS.
13. Contraction Time: Adjustable, from 2-90 seconds, 1sec./step, (EMS only).
14. Relaxation Time: Adjustable, from 2-90 seconds, 1sec./step, (EMS only).
15. Ramp Time: Adjustable, from 1-8 seconds, 1sec./step, (EMS only).
16. Patient compliance meter: The patient compliance timer can memorize 100 sets of therapy session records; the total record time is 400 hours; 240 minutes for a single therapy session.
17. Digital LCD display.
18. Low battery indicator.
19. Power: DC 9V battery.
20. Size: MH8000 Series, 13.6(L)x7(W)x2.65(H)(cm).
21. Weight: MH8000 Series, 162 grams (battery included).
24. Tolerance: +/- 10%

The Set contains: 1 device; 2 WA01 Lead Wires; 4 EB4040 Electrodes; 1 BA01 super heavy duty battery; 1 Instruction Manual; 1 SB01 Soft Pouch.

If you don't feel comfortable yet to make your choice, we recommend you to consult the manual which can be found here !

ISO9001　　ISO13485　　FDA(510k)